coreMQTT  v1.1.0
MQTT 3.1.1 Client Library

Architecture of the MQTT library.

This MQTT client library provides an implementation of the MQTT 3.1.1 specification. It is optimized for resource constrained devices and does not allocate any memory.

Interfaces and Callbacks

The MQTT library relies on interfaces to dissociate itself from platform specific functionality, such as the transport layer or maintaining time. Interfaces used by MQTT are simply function pointers with expectations of behavior.

The MQTT library expects the application to provide implementations for the following interfaces:

Function Pointer Use
TransportRecv_t Receiving data from an established network connection.
TransportSend_t Sending data over an established network connection.
MQTTGetCurrentTimeFunc_t Obtaining timestamps for complying with user-specified timeouts and the MQTT keep-alive mechanism.
MQTTEventCallback_t Returning packets received from the network to the user application after deserialization.

Serializers and Deserializers

The managed MQTT API in core_mqtt.h uses a set of serialization and deserialization functions declared in core_mqtt_serializer.h. If a user does not want to use the functionality provided by the managed API, these low-level functions can be used directly:

Sessions and State

The MQTT 3.1.1 protocol allows for a client and server to maintain persistent sessions, which can be resumed after a reconnect. The elements of a session stored by this client library consist of the states of incomplete publishes with Quality of Service levels of 1 (at least once), or 2 (exactly once). These states are stored in the arrays MQTTContext_t::outgoingPublishRecords and MQTTContext_t::incomingPublishRecords; the length of each of these arrays can be configured with MQTT_STATE_ARRAY_MAX_COUNT. This library does not store any subscription information, nor any information for QoS 0 publishes.

When resuming a persistent session, the client library will resend PUBRELs for all PUBRECs that had been received for incomplete outgoing QoS 2 publishes. If the broker does not resume the session, then all state information in the client will be reset.

The library stores only the state of incomplete publishes and not the publish payloads. It is the responsibility of the user application to save publish payloads until the publish is complete. If a persistent session is resumed, then MQTT_PublishToResend should be called to obtain the packet identifiers of incomplete publishes, followed by a call to MQTT_Publish to resend the unacknowledged publish.

Packet Reception

MQTT Packets are received from the network with calls to MQTT_ProcessLoop or MQTT_ReceiveLoop. These functions are mostly identical, with the exception of keep-alive; the former sends ping requests and processes ping responses to ensure the MQTT session does not remain idle for more than the keep-alive interval, while the latter does not. Since calls to MQTT_Publish, MQTT_Subscribe, and MQTT_Unsubscribe only send packets and do not wait for acknowledgments, a call to MQTT_ProcessLoop or MQTT_ReceiveLoop must follow in order to receive any expected acknowledgment. The exception is MQTT_Connect; since a MQTT session cannot be considered established until the server acknowledges a CONNECT packet with a CONNACK, the function waits until the CONNACK is received.

Runtime Timeouts passed to MQTT library

MQTT_Connect, MQTT_ProcessLoop, and MQTT_ReceiveLoop all accept a timeout parameter for packet reception.
For the MQTT_Connect, if this value is set to 0, then instead of a time-based loop, it will attempt to call the transport receive function up to a maximum number of retries, which is defined by MQTT_MAX_CONNACK_RECEIVE_RETRY_COUNT.

For MQTT_ProcessLoop and MQTT_ReceiveLoop, the timeout value represents the minimum duration that will be spent in the function, provided there are no network errors. Should the timeout be set to 0, then the loop will run for a single iteration. A single iteration of a loop consists of an attempt to receive a single byte from the network, and if the single byte receive was successful, then attempt(s) to receive the rest of the packet (with retry attempts governed by MQTT_RECV_POLLING_TIMEOUT_MS), followed by sending acknowledgement response, if needed (with retry attempts governed by MQTT_SEND_RETRY_TIMEOUT_MS), and then, finally deserialization of the packet received and a call to the application callback. If the first read did not succeed, then instead the library checks if a ping request needs to be sent (only for the process loop).

See the below diagrams for a representation of the above flows:

MQTT Connect Diagram MQTT ProcessLoop Diagram MQTT ReceiveLoop Diagram
MQTT Connect MQTT Process Loop MQTT Receive Loop


The MQTT standard specifies a keep-alive mechanism to detect half-open or otherwise unusable network connections. An MQTT client will send periodic ping requests (PINGREQ) to the server if the connection is idle. The MQTT server must respond to ping requests with a ping response (PINGRESP).

In this library, MQTT_ProcessLoop handles sending of PINGREQs and processing corresponding PINGRESPs to comply with the keep-alive interval set in MQTTContext_t::keepAliveIntervalSec.

The standard does not specify the time duration within which the server has to respond to a ping request, noting only a "reasonable amount of time". If the response to a ping request is not received within MQTT_PINGRESP_TIMEOUT_MS, this library assumes that the connection is dead.

If MQTT_ReceiveLoop is used instead of MQTT_ProcessLoop, then no ping requests are sent. The application must ensure the connection does not remain idle for more than the keep-alive interval by calling MQTT_Ping to send ping requests. The timestamp in MQTTContext_t::lastPacketTime indicates when a packet was last sent by the library.

Sending any ping request sets the MQTTContext_t::waitingForPingResp flag. This flag is cleared by MQTT_ProcessLoop when a ping response is received. If MQTT_ReceiveLoop is used instead, then this flag must be cleared manually by the application's callback.