View a markdown version of this page

Supported network configurations - Amazon Elastic VMware Service

Supported network configurations

Amazon Elastic VMware Service supports the following network connections and VPC configurations in both deployment modes. The tables also list what Amazon EVS doesn’t support. In each table, the Supported column shows Yes, No, or Required, and the Notes column gives the condition or the alternative.

Connections to on-premises networks and other VPCs

The following table lists the supported and unsupported connections to on-premises networks and other VPCs.

Configuration Supported Notes

AWS Transit Gateway

Required

You must use a transit gateway to connect an Amazon EVS environment to your on-premises networks. The transit gateway does not learn NSX routes from Amazon VPC Route Server. After you create the environment, add static routes for the NSX overlay networks to the transit gateway route tables.

Direct Connect with a transit gateway

Yes

Associate the transit gateway with a Direct Connect gateway. For more information, see Direct Connect gateways and transit gateway associations.

AWS Site-to-Site VPN attached to a transit gateway

Yes

For more information, see AWS Site-to-Site VPN attachments in the Amazon VPC Transit Gateway User Guide. You can combine Site-to-Site VPN with Direct Connect. For more information, see Private IP AWS Site-to-Site VPN with Direct Connect.

AWS Cloud WAN

Yes

Like a transit gateway, Cloud WAN does not learn NSX routes from VPC Route Server. Add static routes for the NSX overlay networks.

Direct Connect private virtual interface (VIF) to the Amazon EVS VPC

No

Use a transit gateway with Direct Connect.

AWS Site-to-Site VPN that terminates directly in the Amazon EVS VPC

No

Attach the Site-to-Site VPN connection to a transit gateway.

VPC peering

No

Use a transit gateway or Cloud WAN to connect to other VPCs.

For steps to connect on-premises networks, see Set up VPC Route Server and on-premises connectivity.

Internet access

The following table lists the supported options for internet access.

Configuration Supported Notes

NAT gateway for outbound internet access

Yes

Amazon EVS requires a NAT gateway for outbound internet connectivity. In Self-deployed mode, the VMware Cloud Foundation (VCF) Installer reaches the Broadcom online depot through it. For the subnet and route rules, see Gateway route requirements.

Elastic IP addresses on the HCX VLAN subnet

Yes

Amazon EVS supports associating Elastic IP addresses only with the HCX VLAN subnet, for HCX internet connectivity. For more information, see Plan HCX connectivity.

Inspection of north-south traffic

Yes

You can place AWS Network Firewall or partner firewalls behind a Gateway Load Balancer at the internet ingress and egress points of the VPC.

VPC and subnets

The following table lists the supported and unsupported VPC and subnet configurations.

Configuration Supported Notes

IPv4 VPC CIDR block of /22 or larger

Required

For sizing, see Plan your VPC and VLAN subnets.

More than one Amazon EVS environment in the same VPC

No

Each Amazon EVS environment needs its own VPC. A VPC can’t be used by another deployed Amazon EVS environment.

IPv6

No

Amazon EVS supports IPv4 only. Amazon EVS also does not support private IPv6 Global Unicast Address (GUA) CIDRs.

Subnets in more than one Availability Zone

No

An Amazon EVS environment runs in one Availability Zone. All VPC subnets that Amazon EVS uses must be in that Availability Zone.

VPC, subnets, and environment in different accounts

No

You must create the VPC, the subnets, and the Amazon EVS environment in the same account. Amazon EVS does not support cross-account sharing of VPC subnets or of environments.

Secondary VPC CIDR block for the public HCX CIDR

Required

Required for HCX internet connectivity. You add the public IPv4 CIDR block from your IPAM pool to the VPC as an additional CIDR. For more information, see Plan HCX connectivity.

Custom route table during environment creation

No

During creation, the VLAN subnets are implicitly associated with the VPC main route table. Configure the main route table with routes to your DNS servers and on-premises systems. Use a custom route table only after the environment is created.

Explicit route table association of the VLAN subnets after creation

Required

After the environment is created, associate the VLAN subnets explicitly with a route table. Without this, NSX connectivity fails. For more information, see Associate VLAN subnets with a route table.

Gateway VPC endpoint for Amazon S3

No

Use an interface VPC endpoint with AWS PrivateLink for Amazon S3. For more information, see AWS PrivateLink for Amazon S3 in the Amazon Simple Storage Service User Guide.

Traffic control and workload placement

The following table lists the supported and unsupported options for traffic control and workload placement.

Configuration Supported Notes

Security groups on the network interfaces in VLAN subnets

No

Security groups do not apply to traffic on the elastic network interfaces in Amazon EVS VLAN subnets. Use a network ACL to control traffic to and from the VLAN subnets. For more information, see Create a network ACL for VLAN subnet traffic.

Network ACLs on VLAN subnets

Yes

You can use the default network ACL of the VPC or a custom network ACL. For HCX internet connectivity, we strongly recommend a custom network ACL dedicated to the HCX VLAN subnet.

VCF management appliances on VLAN subnets

Yes

vCenter, NSX Manager, the NSX Edge nodes, SDDC Manager, and HCX appliances run on the VLAN subnets.

Guest workload VMs on VLAN subnets

No

The VLAN subnets carry VCF underlay traffic only. Deploy workload VMs on NSX overlay networks.

NSX Federation

Yes

Use the expansion VLAN subnets for Federation traffic. For more information, see Set up NSX Federation.

For the NSX Edge and routing limits, see Plan NSX Edge and VPC Route Server design.