InstancePortInfo - Amazon Lightsail

InstancePortInfo

Describes information about ports for an Amazon Lightsail instance.

Contents

accessDirection

The access direction (inbound or outbound).

Note

Lightsail currently supports only inbound access direction.

Type: String

Valid Values: inbound | outbound

Required: No

accessFrom

The location from which access is allowed. For example, Anywhere (0.0.0.0/0), or Custom if a specific IP address or range of IP addresses is allowed.

Type: String

Required: No

accessType

The type of access (Public or Private).

Type: String

Valid Values: Public | Private

Required: No

cidrListAliases

An alias that defines access for a preconfigured range of IP addresses.

The only alias currently supported is lightsail-connect, which allows IP addresses of the browser-based RDP/SSH client in the Lightsail console to connect to your instance.

Type: Array of strings

Required: No

cidrs

The IPv4 address, or range of IPv4 addresses (in CIDR notation) that are allowed to connect to an instance through the ports, and the protocol.

Note

The ipv6Cidrs parameter lists the IPv6 addresses that are allowed to connect to an instance.

For more information about CIDR block notation, see Classless Inter-Domain Routing on Wikipedia.

Type: Array of strings

Required: No

commonName

The common name of the port information.

Type: String

Required: No

fromPort

The first port in a range of open ports on an instance.

Allowed ports:

  • TCP and UDP - 0 to 65535

  • ICMP - The ICMP type for IPv4 addresses. For example, specify 8 as the fromPort (ICMP type), and -1 as the toPort (ICMP code), to enable ICMP Ping. For more information, see Control Messages on Wikipedia.

  • ICMPv6 - The ICMP type for IPv6 addresses. For example, specify 128 as the fromPort (ICMPv6 type), and 0 as toPort (ICMPv6 code). For more information, see Internet Control Message Protocol for IPv6.

Type: Integer

Valid Range: Minimum value of -1. Maximum value of 65535.

Required: No

ipv6Cidrs

The IPv6 address, or range of IPv6 addresses (in CIDR notation) that are allowed to connect to an instance through the ports, and the protocol. Only devices with an IPv6 address can connect to an instance through IPv6; otherwise, IPv4 should be used.

Note

The cidrs parameter lists the IPv4 addresses that are allowed to connect to an instance.

For more information about CIDR block notation, see Classless Inter-Domain Routing on Wikipedia.

Type: Array of strings

Required: No

protocol

The IP protocol name.

The name can be one of the following:

  • tcp - Transmission Control Protocol (TCP) provides reliable, ordered, and error-checked delivery of streamed data between applications running on hosts communicating by an IP network. If you have an application that doesn't require reliable data stream service, use UDP instead.

  • all - All transport layer protocol types. For more general information, see Transport layer on Wikipedia.

  • udp - With User Datagram Protocol (UDP), computer applications can send messages (or datagrams) to other hosts on an Internet Protocol (IP) network. Prior communications are not required to set up transmission channels or data paths. Applications that don't require reliable data stream service can use UDP, which provides a connectionless datagram service that emphasizes reduced latency over reliability. If you do require reliable data stream service, use TCP instead.

  • icmp - Internet Control Message Protocol (ICMP) is used to send error messages and operational information indicating success or failure when communicating with an instance. For example, an error is indicated when an instance could not be reached. When you specify icmp as the protocol, you must specify the ICMP type using the fromPort parameter, and ICMP code using the toPort parameter.

  • icmp6 - Internet Control Message Protocol (ICMP) for IPv6. When you specify icmp6 as the protocol, you must specify the ICMP type using the fromPort parameter, and ICMP code using the toPort parameter.

Type: String

Valid Values: tcp | all | udp | icmp | icmpv6

Required: No

toPort

The last port in a range of open ports on an instance.

Allowed ports:

  • TCP and UDP - 0 to 65535

  • ICMP - The ICMP code for IPv4 addresses. For example, specify 8 as the fromPort (ICMP type), and -1 as the toPort (ICMP code), to enable ICMP Ping. For more information, see Control Messages on Wikipedia.

  • ICMPv6 - The ICMP code for IPv6 addresses. For example, specify 128 as the fromPort (ICMPv6 type), and 0 as toPort (ICMPv6 code). For more information, see Internet Control Message Protocol for IPv6.

Type: Integer

Valid Range: Minimum value of -1. Maximum value of 65535.

Required: No

See Also

For more information about using this API in one of the language-specific AWS SDKs, see the following: